smartctl 6.3 2014-07-26 r3976 [i686-w64-mingw32-win7(64)-sp1] (sf-6.3-1)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST3500620SS
Revision:             MS0A
User Capacity:        500'107'862'016 bytes [500 GB]
Logical block size:   512 bytes
Rotation Rate:        7200 rpm
Logical Unit id:      0x5000c5000d7cff03
Serial number:        9QMBYYFB
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Nov 05 17:28:47 2014 WEST
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Disabled or Not Supported
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     28 C
Drive Trip Temperature:        68 C

Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 4194071079
  Blocks received from initiator = 727949543
  Blocks read from cache and sent to initiator = 848709174
  Number of read and write commands whose size <= segment size = 997691554
  Number of read and write commands whose size > segment size = 0

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 37473.32
  number of minutes until next internal SMART test = 45

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   661361001        9         0  661361010   661361010     112291.030           0
write:         0        0         0         0          0       2591.610           0
verify: 319585782        7         0  319585789   319585789      56853.253           0

Non-medium error count:        4

SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background long   Completed                  16   37473                 - [-   -    -]
# 2  Background short  Completed                  16     212                 - [-   -    -]
# 3  Background long   Completed                  16       2                 - [-   -    -]
# 4  Background short  Completed                  16       1                 - [-   -    -]

Long (extended) Self Test duration: 6798 seconds [113.3 minutes]

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 37473:19 [2248399 minutes]
    Number of background scans performed: 237,  scan progress: 21.10%
    Number of background medium scans performed: 237

   #  when        lba(hex)    [sk,asc,ascq]    reassign_status
 33024 1077:02  0008010003110081  [a,92,dd]   Reserved [0x0]
 33025 12026:27  0080010003110081  [f,5f,b6]   Reserved [0x0]
 33026 21127:42  0020010003110081  [f,c9,a5]   Reserved [0x0]

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 1.5 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5000d7cff01
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 3 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5000d7cff02
    attached SAS address = 0x500e01800006c2c2
    attached phy identifier = 0
    Invalid DWORD count = 4
    Running disparity error count = 4
    Loss of DWORD synchronization = 1
    Phy reset problem = 0