smartctl 6.3 2014-07-26 r3976 [i686-w64-mingw32-win7(64)-sp1] (sf-6.3-1)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST500NM0001
Revision:             PS07
Compliance:           SPC-4
User Capacity:        500'107'862'016 bytes [500 GB]
Logical block size:   512 bytes
Rotation Rate:        7200 rpm
Form Factor:          3.5 inches
Logical Unit id:      0x5000c500427c4fe3
Serial number:        Z1M1042V
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Wed Nov 05 22:51:51 2014 WEST
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Disabled or Not Supported
Read Cache is:        Enabled
Writeback Cache is:   Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     29 C
Drive Trip Temperature:        68 C

Manufactured in week 40 of year 2012
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  23
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  6530
Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 2527876735
  Blocks received from initiator = 2802312114
  Blocks read from cache and sent to initiator = 31821344
  Number of read and write commands whose size <= segment size = 25086914
  Number of read and write commands whose size > segment size = 0

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 8587.58
  number of minutes until next internal SMART test = 38

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   1090168567        0         0  1090168567          0      26356.656           0
write:         0        0         0         0          0       1439.577           0
verify: 3305839084        0         0  3305839084          0      13734.056           0

Non-medium error count:        3

SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background long   Completed                  32    8586                 - [-   -    -]
# 2  Background short  Completed                  32      24                 - [-   -    -]

Long (extended) Self Test duration: 7200 seconds [120.0 minutes]

Background scan results log
  Status: scan is active
    Accumulated power on time, hours:minutes 8587:35 [515255 minutes]
    Number of background scans performed: 34,  scan progress: 94.86%
    Number of background medium scans performed: 34

Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 1.5 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500427c4fe1
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: SAS or SATA device
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 3 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c500427c4fe2
    attached SAS address = 0x500e01800006c2c2
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0