smartctl 6.5 2016-05-07 r4318 [x86_64-w64-mingw32-win7-sp1] (sf-6.5-1)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST973452SS
Revision:             0005
User Capacity:        73'407'868'928 bytes [73.4 GB]
Logical block size:   512 bytes
Rotation Rate:        15015 rpm
Logical Unit id:      0x5000c5001b0d8abb
Serial number:        6TA006RX0000B1042UHW
Device type:          disk
Transport protocol:   SAS (SPL-3)
Local Time is:        Sat Nov 11 17:39:47 2017 MZ
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled
Read Cache is:        Enabled
Writeback Cache is:   Disabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Current Drive Temperature:     38 C
Drive Trip Temperature:        68 C

Elements in grown defect list: 0

Vendor (Seagate) cache information
  Blocks sent to initiator = 627203136
  Blocks received from initiator = 138564369
  Blocks read from cache and sent to initiator = 450579775
  Number of read and write commands whose size <= segment size = 253559449
  Number of read and write commands whose size > segment size = 0

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 29689.82
  number of minutes until next internal SMART test = 26

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   188234181        0         0  188234181   188234181      10489.900           0
write:         0        0         0         0          0       4552.729           0
verify: 122215155        0         0  122215155   122215155      11709.791           0

Non-medium error count:      139


[GLTSD (Global Logging Target Save Disable) set. Enable Save with '-S on']
SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background long   Completed                   -   29687                 - [-   -    -]
# 2  Background long   Completed                   -   17112                 - [-   -    -]

Long (extended) Self Test duration: 721 seconds [12.0 minutes]

scsiPrintBackgroundResults Failed [scsi response fails sanity test]
Protocol Specific port log page for SAS SSP
relative target port id = 1
  generation code = 0
  number of phys = 1
  phy identifier = 0
    attached device type: SAS or SATA device
    attached reason: loss of dword synchronization
    reason: power on
    negotiated logical link rate: phy enabled; 6 Gbps
    attached initiator port: ssp=1 stp=1 smp=1
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5001b0d8ab9
    attached SAS address = 0x500605b0050f9c20
    attached phy identifier = 3
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0
relative target port id = 2
  generation code = 0
  number of phys = 1
  phy identifier = 1
    attached device type: no device attached
    attached reason: unknown
    reason: unknown
    negotiated logical link rate: phy enabled; 1.5 Gbps
    attached initiator port: ssp=0 stp=0 smp=0
    attached target port: ssp=0 stp=0 smp=0
    SAS address = 0x5000c5001b0d8aba
    attached SAS address = 0x0
    attached phy identifier = 0
    Invalid DWORD count = 0
    Running disparity error count = 0
    Loss of DWORD synchronization = 0
    Phy reset problem = 0
    Phy event descriptors:
     Invalid word count: 0
     Running disparity error count: 0
     Loss of dword synchronization count: 0
     Phy reset problem count: 0