smartctl 6.4 2015-06-04 r4109 [i686-w64-mingw32-win7(64)-sp1] (sf-6.4-1) Copyright (C) 2002-15, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Blue Serial ATA Device Model: WDC WD2500AAJS-75VWA0 Serial Number: WD-WCARZ0106252 LU WWN Device Id: 5 0014ee 10093fabd Firmware Version: 12.01B02 User Capacity: 250'000'000'000 bytes [250 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.5, 3.0 Gb/s Local Time is: Tue Nov 21 16:04:00 2017 MZ SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM level is: 128 (quiet), recommended: 128 APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, frozen [SEC2] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 6480) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 78) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 200 200 051 - 0 3 Spin_Up_Time PO---- 154 151 021 - 5283 4 Start_Stop_Count -O--CK 097 097 000 - 3678 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-- 200 200 051 - 0 9 Power_On_Hours -O--CK 071 071 000 - 21233 10 Spin_Retry_Count -O--C- 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 051 - 0 12 Power_Cycle_Count -O--CK 097 097 000 - 3292 192 Power-Off_Retract_Count -O--CK 200 200 000 - 233 193 Load_Cycle_Count -O--CK 199 199 000 - 3685 194 Temperature_Celsius -O---K 108 098 000 - 39 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--C- 200 200 000 - 0 198 Offline_Uncorrectable ----C- 200 200 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 051 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 SATA NCQ Queued Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 12 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 9 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 9 [8] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 e3 25 0d b6 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 08 00 00 a0 0d e3 01 b6 25 00 00 08 00:00:43.016 DEVICE RESET 9f 6a 25 0d b6 00 00 08 00 00 00 d0 01 00:14:58.666 [RESERVED] 08 08 00 00 f8 0d 6a 01 b6 35 00 00 08 00:00:38.920 DEVICE RESET Error 8 [7] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 60 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 58 25 0d aa 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 c8 00 00 48 0d 57 04 aa 35 00 00 08 00:00:32.864 DEVICE RESET 0f 56 35 0d aa 00 20 08 a0 00 00 00 10 00:14:55.575 [RESERVED] 08 20 00 00 a0 0d 56 0f aa 35 00 00 08 00:00:49.184 DEVICE RESET Error 7 [6] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 cf 25 62 c8 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 08 00 00 38 62 cf 1d c8 35 00 00 08 00:00:22.656 DEVICE RESET 11 ce 35 62 c8 00 20 08 20 00 00 00 1d 01:47:53.934 RECALIBRATE [RET-4] 08 40 00 00 00 62 ce 11 c8 35 00 00 08 00:00:51.208 DEVICE RESET Error 6 [5] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 55 25 62 bd 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 08 00 00 98 62 55 1d bd 35 00 00 08 00:00:43.016 DEVICE RESET 01 55 25 62 bd 00 08 08 40 00 00 00 01 01:47:50.997 [RESERVED] 08 08 00 00 b8 62 55 0f bd 35 00 00 08 00:00:40.968 DEVICE RESET Error 5 [4] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 40 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 5a 25 62 b1 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 10 00 00 a0 62 5a 0f b1 35 00 00 08 00:00:41.024 DEVICE RESET 01 5a 35 62 b1 00 08 08 30 00 00 00 1d 01:47:47.930 [RESERVED] 08 20 00 00 a0 62 f3 01 a5 25 00 00 08 00:00:24.608 DEVICE RESET Error 4 [3] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 20 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 f3 25 62 a5 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 20 00 00 20 62 f3 11 a5 35 00 00 08 00:00:40.992 DEVICE RESET 04 f3 25 62 a5 00 20 08 00 00 00 00 01 01:47:45.011 [RESERVED] 08 20 00 00 e0 62 f2 04 a5 35 00 00 08 00:00:32.800 DEVICE RESET Error 3 [2] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 80 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 a7 25 4a 25 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 08 00 00 f0 4a a7 1d 25 35 00 00 08 00:00:22.656 DEVICE RESET 01 a7 35 4a 25 00 08 08 70 00 00 00 1d 01:20:59.303 [RESERVED] 08 20 00 00 80 4a a6 10 25 35 00 00 08 00:00:34.824 DEVICE RESET Error 2 [1] occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 00 01 08 00 51 00 00 e0 01 00 00 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 00 9e 25 4a 19 00 00 00 00 00 00 00 01 00:00:00.000 NOP [Reserved subcommand] [OBS-ACS-2] 08 10 00 00 00 4a 9e 0f 19 35 00 00 08 00:00:43.016 DEVICE RESET 01 9d 25 4a 19 00 08 08 28 00 00 00 01 01:20:56.222 [RESERVED] 08 08 00 00 58 4a 9d 0f 19 35 00 00 08 00:00:40.968 DEVICE RESET SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 21228 - # 2 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 39 Celsius Power Cycle Min/Max Temperature: 19/39 Celsius Lifetime Min/Max Temperature: 20/49 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: 1/85 Celsius Temperature History Size (Index): 128 (66) Index Estimated Time Temperature Celsius 67 2017-11-21 13:57 29 ********** 68 2017-11-21 13:58 29 ********** 69 2017-11-21 13:59 30 *********** 70 2017-11-21 14:00 30 *********** 71 2017-11-21 14:01 30 *********** 72 2017-11-21 14:02 31 ************ 73 2017-11-21 14:03 31 ************ 74 2017-11-21 14:04 31 ************ 75 2017-11-21 14:05 32 ************* ... ..( 2 skipped). .. ************* 78 2017-11-21 14:08 32 ************* 79 2017-11-21 14:09 33 ************** ... ..( 2 skipped). .. ************** 82 2017-11-21 14:12 33 ************** 83 2017-11-21 14:13 34 *************** ... ..( 5 skipped). .. *************** 89 2017-11-21 14:19 34 *************** 90 2017-11-21 14:20 35 **************** ... ..( 6 skipped). .. **************** 97 2017-11-21 14:27 35 **************** 98 2017-11-21 14:28 36 ***************** ... ..( 8 skipped). .. ***************** 107 2017-11-21 14:37 36 ***************** 108 2017-11-21 14:38 37 ****************** ... ..( 17 skipped). .. ****************** 126 2017-11-21 14:56 37 ****************** 127 2017-11-21 14:57 38 ******************* ... ..( 8 skipped). .. ******************* 8 2017-11-21 15:06 38 ******************* 9 2017-11-21 15:07 39 ******************** 10 2017-11-21 15:08 38 ******************* 11 2017-11-21 15:09 39 ******************** ... ..( 45 skipped). .. ******************** 57 2017-11-21 15:55 39 ******************** 58 2017-11-21 15:56 38 ******************* 59 2017-11-21 15:57 39 ******************** ... ..( 5 skipped). .. ******************** 65 2017-11-21 16:03 39 ******************** 66 2017-11-21 16:04 29 ********** SCT Error Recovery Control: Read: Disabled Write: Disabled Device Statistics (GP/SMART Log 0x04) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x000a 2 0 Device-to-host register FISes sent due to a COMRESET 0x8000 4 8737 Vendor specific